Dual Servo Controller Assembly Instructions - Revision history

Ilya at 23:25, 18 February 2013

2013-02-18T23:25:29Z

2013-02-18T20:21:25Z

2012-01-24T16:24:43Z

2012-01-20T00:41:29Z

2012-01-20T00:38:17Z

2012-01-20T00:37:03Z

2012-01-19T21:33:09Z

2012-01-19T21:32:21Z

2012-01-15T04:50:46Z

2012-01-15T04:50:07Z

@@ Line 1: / Line 1: @@
 Before you begin soldering, spread out the parts you've received and make sure you have everything. You should have all the following components:
 [[File:Tiny Servo Driver 42.JPG|400px|none]]
-For detailed information about each component check out the [[Tiny Servo Driver Bill of Materials]].
+For detailed information about each component check out the [[Dual Servo Controller Bill of Materials]].

@@ Line 1: / Line 1: @@
 Before you begin soldering, spread out the parts you've received and make sure you have everything. You should have all the following components:
 [[File:Tiny Servo Driver 42.JPG|400px|none]]
-For detailed information about each component check out the [[Tiny Servo Driver Bill of Material]].
+For detailed information about each component check out the [[Tiny Servo Driver Bill of Materials]].

← Older revision		Revision as of 00:41, 20 January 2012
Line 81:		Line 81:


−	Now it's time to insert the Attiny85 microcontroller. The pins of the microcontroller come flared out. To make easier to insert the chip you should bend the legs inward a bit. An easy way to do this is against a hard surface, like this:	+	Now it's time to insert the Attiny85 microcontroller. The pins of the microcontroller come flared out. To make it easier to insert the chip you should bend the legs inward a bit. An easy way to do this is against a hard surface, like this:
	[[File:Bend_Chip_Pins.JPG\|400px\|none]]		[[File:Bend_Chip_Pins.JPG\|400px\|none]]

@@ Line 34: / Line 34: @@
-Snip the leads off using your flush cutters. Cut at the base of each lead, you want there to be nothing sticking out of the solder joint. The lead will fling once you snip it so hold with your other hand while cutting.
+Snip the leads off using your flush cutters. Cut at the base of each lead, you want there to be nothing sticking out of the solder joint. The lead will fling once you snip it so hold it with your other hand while cutting.
 [[File:Tiny_Servo_Driver_10.JPG|400px|none]]
 [[File:Tiny_Servo_Driver_11.JPG|400px|none]]

← Older revision		Revision as of 00:37, 20 January 2012
Line 12:		Line 12:


−	Next insert the diode. The diode needs to be inserted the correct orientation. Make sure that, once inserted, the stripe on the diode matches up with the stripe on the PCB graphic.	+	Next insert the diode. The diode needs to be inserted in the correct orientation. Make sure that, once inserted, the stripe on the diode matches up with the stripe on the PCB graphic.
	[[File:Tiny_Servo_Driver_03.JPG\|400px\|none]]		[[File:Tiny_Servo_Driver_03.JPG\|400px\|none]]

← Older revision	Revision as of 20:21, 18 February 2013
(No difference)

@@ Line 79: / Line 79: @@
 But if you do decided to include the header, solder it in place using the technique you used to solder the previous two headers.
 [[File:Tiny_Servo_Driver_26.JPG|400px|none]]
 Now it's time to insert the Attiny85 microcontroller. The pins of the microcontroller come flared out. To make easier to insert the chip you should bend the legs inward a bit. An easy way to do this is against a hard surface, like this:

← Older revision		Revision as of 21:32, 19 January 2012
Line 79:		Line 79:
	But if you do decided to include the header, solder it in place using the technique you used to solder the previous two headers.		But if you do decided to include the header, solder it in place using the technique you used to solder the previous two headers.
	[[File:Tiny_Servo_Driver_26.JPG\|400px\|none]]		[[File:Tiny_Servo_Driver_26.JPG\|400px\|none]]
		+
		+	Now it's time to insert the Attiny85 microcontroller. The pins of the microcontroller come flared out. To make easier to insert the chip you should bend the legs inward a bit. An easy way to do this is against a hard surface, like this:
		+	[[File:Bend_Chip_Pins.JPG\|400px\|none]]

← Older revision		Revision as of 04:50, 15 January 2012
Line 110:		Line 110:

	And you're finished! High-fives all around.		And you're finished! High-fives all around.
−	~~[[File:Tiny_Servo_Driver_40.JPG\|400px\|none]]~~
	[[File:Tiny_Servo_Driver_41.JPG\|400px\|none]]		[[File:Tiny_Servo_Driver_41.JPG\|400px\|none]]

← Older revision		Revision as of 04:50, 15 January 2012
Line 107:		Line 107:
	[[File:Tiny_Servo_Driver_38.JPG\|400px\|none]]		[[File:Tiny_Servo_Driver_38.JPG\|400px\|none]]
	[[File:Tiny_Servo_Driver_39.JPG\|400px\|none]]		[[File:Tiny_Servo_Driver_39.JPG\|400px\|none]]
		+
		+
		+	And you're finished! High-fives all around.
		+	[[File:Tiny_Servo_Driver_40.JPG\|400px\|none]]
		+	[[File:Tiny_Servo_Driver_41.JPG\|400px\|none]]